Peerless ST640P-S Instrukcja Obsługi Pobierz pdf (Strona 9)

9 of 38

ISSUED: 11-26-07 SHEET #: 202-9256-6 04-05-11

• Always use an assistant or mechanical lifting equipment

to safely lift and position the ﬂ at panel display.

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

• Be careful not to pinch ﬁ ngers when pushing display from

the bottom.

For preset tilt angles use Increlok

™ and for custom

tilt angle use ratchet handle.

INCRELOK™: The display can be locked into a

pre-set tilt position of -5

°, 0°, 5°, 10° or 15°. Use

locator hole to ﬁ nd tilt position hole and tilt display to

align holes. Tighten IncreLok™ tilt locking screws on

both tilt brackets to lock tilt as shown in detail 2.

Ratchet Handle: Loosen ratchet handle (refer to

step 3 for tension adjustment of handle).

Push or pull

from top or bottom of display to adjust tilt as shown

in ﬁ gure 4.1. The tilt can be adjusted to a maximum

of 15° forward or 5° backward.

Tension Adjustment of Ratchet Handle: Adjust

tension in tilt brackets (BB & CC) by rotating ratchet

handle. NOTE: If obstruction prevents ratchet handle

from rotating, pull handle out while turning will allow

handle to reposition without tightening. Release and

turn handle to tighten or loosen.

Mounting Display: Ratchet handle must be in

the up or down position or interference will occur

while hooking tilt brackets to wall plate (AA). Slowly

hook tilt brackets (BB & CC) onto wall plate (AA)

and swing display down as shown in ﬁ g. 3.1. Tilt

bracket hooks must fully engage wall plate as shown

in detail 1. Using phillips screw driver or security

allen wrench (FF), turn safety/security screws on tilt

brackets (BB & CC) clockwise till screw tip securely

contacts wall plate as shown in cross section.

Display Adjustment: Display can be adjusted

horizontally by loosening safety/security screws on

tilt brackets (BB & CC) three full turns. Adjust display

as shown in ﬁ gure 3.2. Tighten safety/security

screws on tilt brackets till screw tip securely contacts

wall plate as shown in cross section.

Removing Display: To remove display from mount,

loosen safety screws, swing display away from

mount, and lift display off of mount.

Mounting and Removing Flat Panel Display

Adjusting the Tilt Angle of the Flat Panel

Display

WARNING

All other brand and product names are trademarks or registered trademarks of their respective owners.

DETAIL 2

ﬁ g 4.1

IncreLok™ TILT

LOCKING SCREW

LOCATOR

HOLE

RATCHET

HANDLE

TILT

POSITION

HOLES

ﬁ g 3.2

SAFETY/

SECURITY

SCREW

CROSS SECTION

DETAIL 1

ﬁ g 3.1

RATCHET

HANDLE

Peerless Industries, Inc.

2300 White Oak Circle

Aurora, Il 60502

www.peerlessmounts.com

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 37 38

Komentarze do niniejszej Instrukcji

Brak uwag

Peerless ST640P-S Instrukcja Obsługi Strona 9

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Uchwyty ścienne do płaskich paneli Peerless ST640P-S